Vehicles
Sections
177 not categorized PORSCHE 930 PROPSCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 930 1975-77 (includes uncategorized and accessory items) 99610515201
From $61.21
Make a selection
$120.40
Make a selection 95542101001 - inexpensive alternative to a complete part. - tested quality parts
$178.20
Make a selection ST1032X36T This thin spanner wrench is 32 x36 mm with an 8 mm overall thickness and a length of 12 inches. The 32 mm end is needed for proper removal and reinstallation of the tie rods on 911 turbo, 1975-89- a must when upgrading to turbo tie rods. The 36 mm end is needed for proper adjustment of rear ride height on 911 1977-89. please call our office for availability. General Fitment930 1975-77911 1978-83 911 1984-86 911 1987-89
$75.85
Make a selection ST313 This professional-grade heavy duty bench clamp was designed fro the start to securely carry the full weight of an air-cooled, twin turbo boxer engine with all the trimmings. Properly suited for a work bench. General Fitment356 1950-59356 1960-65 912 1965-69 914 1970-76 911 1965-69 911 1994-98 911 1989-94 911 1987-89 911 1984-86 911 1978-83 930 1975-77 911 1974-77 911 1970-73
$325.00
Make a selection STP215 This oil seal arbor is needed for the proper installation of oil seal on flywheel side of crankshaft. please call our office for availability. General Fitment911 1965-69911 1970-73 911 1974-77 930 1975-77
$189.95
Make a selection STP240 This dial gauge holder is needed to properly measure crank shaft flywheel and pulley end-play. Can also be universally to check clearances and run-out. Applicable: most every Porsche and vw air-cooled engine. Please call our office for availability. General Fitment356 1950-59912 1965-69 914 1970-76 911 1965-69 911 1994-98 911 1989-94 911 1987-89 911 1984-86 911 1978-83 930 1975-77 911 1974-77 911 1970-73
$125.55
Make a selection 906634 Will ship when available. General Fitment911 1974-77930 1975-77 911 1978-83 911 1984-86 911 1987-89
$125.90
Make a selection ER2011000 Monoballs deliver precise, razor sharp handling. but rapid wear has made them impractical for all but the most serious racers. Not anymore! Weather seals - our proprietary-design monoball cartridges have weather seals to keep dirt out and extend product life. this is the only monoball suitable for street or extended track use. dirt and water contaminate ordinary products and accelerate wear. Performance - today’s sticky tire compounds generate corner loads that easily compress factory rubber bushings causing wandering alignment settings. Camber and toe flop around upredictably. weather-sealed monoball cartridges replace compliant factory rubber bushings with hardened-steel spherical bearings. Unlike...(choose a part on the right to read more) General Fitment914 1970-76911 1987-89 911 1984-86 911 1978-83 930 1975-77 911 1974-77 911 1970-73 911 1965-69 912 1965-69
$299.95
Make a selection 90155921020E Replace your old or faded badge with a beautiful new one and get all the parts to do it properly. This kit includes a new gold-tone Porsche hood badge, badge gasket, and two emblem nuts. General Fitment911 1965-69944 1982-85 944 1985-88 944 1989-91 968 1992-95 924 1976-79 924 1980-85 924 1986-88 914 1970-76 912 1965-69 911 1984-86 911 1970-73 911 1974-77 930 1975-77 911 1978-83 911 1987-89 911 1989-94 911 1994-98 928 1978-82 928 1983-86 928 1987-91 928 1992-95
$182.24
Make a selection 846R1010 Brey-krause harness guide bars properly locate a racing shoulder harness relative to the driver. Harness guides also prevent excessive shifting and fatigue of the driver during the high g loads of cornering and braking. Brey-krause harness guide bars are carefully engineered to transfer these forces to factory supplied points that are designed to take the load. General Fitment911 1994-98911 1989-94 911 1974-77 930 1975-77 911 1978-83 911 1984-86 911 1987-89
$359.95
Make a selection 910185 Brey-krause harness products provide a variety of solutions for Porsche drivers utilizing driving harnesses. Where harnesses are mounted to factory mounts, the brey-krause harness guide bars ensures that the harnesses stay positioned properly. The brey-krause harness mount bars additionally allow the harnesses to be mounted directly to the bar for proper positioning. The brey-krause harness products are easy to install and remove, use only existing holes and mounting points, and will not damage the car in any way. General Fitment911 1974-77930 1975-77 911 1978-83 911 1984-86 911 1987-89 911 1970-73 911 1965-69 912 1965-69
$440.00
Make a selection 15500021 Designed to prolong the life of your turbocharger, this greddy turbo timer allows your Porsche to idle the engine for a timed period, with the ignition key removed. This conveniently allows the engine oil and turbo center cartridge to cool down properly and prolong turbo and oil life. The run time can be programmed by the user or utilize it’s “full auto mode”, which estimate the driving rpm according to the vehicle’s alternator signal and then recommend a count down time. To prevent theft, the unit includes a parking brake and speedo hook-up which disengage operation if there is an attempt to move the vehicle without the key. The unit also includes a stopwatch/lap timer and attack modes along with a bui...(choose a part on the right to read more) General Fitment911 2005-08911 TURBO/GT2 2001-05 911 1994-98 911 1989-94 911 1987-89 911 1984-86 911 1978-83 930 1975-77 944 1989-91 944 1985-88
$124.63
Make a selection ER2290000 Diy kit - front control arm rubber bushings are now available as a kit for self-installation. in addition to a complete set of 4 OEM spec rubber bushings, the kit includes proprietary installation tools and instructions, which are essential for successful installation. use a pipe clamp or shop press to complete the install. General Fitment914 1970-76912 1965-69 911 1965-69 911 1970-73 911 1974-77 930 1975-77 911 1978-83 911 1984-86 911 1987-89
$249.00
Make a selection P280B This ball joint pin wrench socket has a 1/2" drive and a pin reinforcement sleeve, needed for the proper removal and reinstallation of ball joint nuts w/o damage to the pin wrench socket or nut. Applicable: Porsche model - 911 ‘65-'89, 912, 914. General Fitment911 1965-69911 1987-89 911 1984-86 911 1978-83 930 1975-77 911 1974-77 911 1970-73 912 1965-69 914 1970-76
$115.00
Make a selection GB1 Brey-krause harness guide bars properly locate a racing shoulder harness relative to the driver. Harness guides also prevent excessive shifting and fatigue of the driver during the high g loads of cornering and braking. Brey-krause harness guide bars are carefully engineered to transfer these forces to factory supplied points that are designed to take the load. Superior materials and workmanship do the job while having an appearance worthy of a Porsche. General Fitment911 1974-77930 1975-77 911 1978-83 911 1984-86 911 1987-89 911 1989-94
$450.00
Make a selection PP34583 To correctly replace your heat exchangers, we recommend using new original-style nuts. Each nut is designed for proper heat dissipation, expansion, and holding control. Sold as a complete set of three per heat exchanger; fits left or right side. Need two sets for both heat exchangers. General Fitment911 1965-69911 1970-73 911 1974-77 930 1975-77 911 1978-83 911 1987-89 911 1984-86 911 1989-94 911 1994-98 914 1970-76
$13.50
Make a selection RSKBPLRND Small round ball shift knob - black satin polypropylene plastic - threads onto rennshift - 49mm. Designed to fit the rennshift shifters, but will fit 914 and 911 shifters. Please measure your shifter thread and include in your order. General Fitment914 1970-76911 1965-69 911 1984-86 911 1978-83 930 1975-77 911 1974-77 911 1970-73
$51.95
Make a selection ER2290002 Diy kit - rear 914 control arm rubber bushings are now available as a kit for self-installation. in addition to a complete set of 4 OEM spec rubber bushings, the kit includes proprietary installation tools and instructions, which are essential for successful installation plus the rear control arm shafts use a pipe clamp or shop press to complete the install. General Fitment914 1970-76911 1965-69 911 1970-73 911 1974-77 930 1975-77 911 1978-83 911 1984-86 911 1987-89
$439.99
Make a selection STP223 This synchro engagement kit is needed for the proper removal of syncro rings from the gear. General Fitment930 1975-77911 1987-89 911 1984-86 911 1978-83
$175.00
Make a selection STP216 This oil seal arbor is needed for the proper installation of oil seal on pulley side of crank shaft. General Fitment911 1987-89911 1984-86 911 1978-83 930 1975-77 911 1974-77 911 1970-73 911 1965-69
$104.50
Make a selection FVD10397506 Carrillo is one of the most respected connecting rod manufacturers in competitive motor sports. Carrillo rods are constructed from their propriety alloy and forged to their custom specifications. The rods are then fully machined to guarantee the removal of all surface imperfections. After heat treatment, each connecting rod is magnaflux inspected and hardness checked, then machined to final size. Each set is balanced and then shot-peened to achieve the ultimate in strength and fatigue properties. General Fitment911 1970-73911 1974-77 930 1975-77
$2,434.30
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |